• All instructions given on the charger label and in the Charger User Guide should be read and understood before attempting to use the charger
• Do not use chargers for any purpose other than charging the batteries for which they have been specified
• Batteries contain large amounts of electrical energy. Take care not to short circuit battery terminals and avoid connecting or disconnecting your charger before the mains supply to the charger is turned off.
• Lead acid batteries can give off hydrogen gas which is explosive in sufficient concentration. Do not cause sparks or use naked flames in the proximity of the batteries. Always ensure adequate ventilation
• Ensure that the charger is of the correct rating and setting for the batteries with which it is to be used.
• Do not use outdoors or in wet or damp environments.
• Do not cover or obstruct the ventilation slots.

Approvals

Built at the ISO 9001 certified site in Manchester, the MTC and High Frequency ranges conform to the following approvals.

• EN 60335 - 1
• EN 60335 - 2 - 29
• These approvals relate to Safety

• EN 50081 - 1 - 1992 (Emissions)
• EN 50082 - 2 - 1995 (Immunity)
• These approvals fall within the CE mark which applies to the MTC and High Frequency ranges.

Versions of the following models have been KEMA approved (Netherlands Safety Authority):

• 24V 4A MTC
• 24V 6A MTC
• 24V 7A MTC
• 24V 8A MTC
• 24V 6A HF Traveller
• 24V 10A HF Traveller

• Class F transformer installation
• Full wave rectification
• Designed and built in Britain

ER35
Mobile, user friendly boost charger with reverse polarity, thermal cutout and alternator protection. Battery condition indicator and ammeter. 6/12/24V DC. Charging output 35A (47A RMS). Switchable boost up to 150A (200A RMS).

CV65
Mobile, fully automatic, constant voltage boost charger with reverse polarity, alternator and no battery protection. Bar graph, voltmeter and ammeter and safety timer suitable for unattended charging of all types of starter batteries. 12/24V DC charging output upto 65A (87A RMS). Switchable boost upto 250A (340A RMS).

FC80MF
Mobile, rugged, boost charger with reverse polairty, alternator and no battery protection. 0-90m timer, variable charging settings, low battery charge switch, analogue ammeter and battery condition indicators. Low/Maintenance Free/High/Boost selector switch. 12/24V DC charging output up to 80A (110A RMS), boost up to 400A (540A RMS).

FC100MF
Mobile, robust, boost charger with reverse polairty, alternator and no battery protection. 0-90m timer, variable charging settings, low battery start switch, analogue ammeter and battery condition indicators. Low/Maintenance Free/High/Boost selector switch. 12/24V DC charging output up to 100A (135A RMS), boost up to 450A (600A RMS).

FC110MF
Mobile, robust, boost charger with reverse polairty, alternator and no battery protection. 0-90m timer, variable charging settings, low battery start switch, analogue ammeter and battery condition indicators. Low/Maintenance Free/High/Boost selector switch. 6/12/24V DC charging output up to 110A (150A RMS), boost up to 500A (670A RMS).

Bench and Specialist Chargers
Davenset commercial chargers are designed to charge a number of batteries simultaneously and can be bench or wall mounted. Charge current and voltage control are effected by coarse and fine tapping switches from main transformer, with both units protected from overload by DC magnetic circuit breakers. Lead sets can be supplied

STC 10/72
Bench or wall mounted charger, reverse polarity protected, AC and DC circuit breakers, current control with coarse and fine 6 stage rotary switches and output ammeter. 6-72V DC up to 10A (13A RMS). For charging 1 to 12/16V batteries, 1 to 6/12V batteries, 1 to 3/24V batteries or any combination of batteries up to 72V connected in series.
Size: 502H x 540W x 342D (mm) Wt 38.5kg.

STC 20/72
Bench or wall mounted charger with two independent charging circuits each as STC 10/72 (above)
Size: 502H x 540W x 342D (mm) Wt 48.5kg.

CV10
Fully automatic, current limited, constant voltage charger with reverse polarity, alternator and no battery protection. 6/12/24Volts DC output to 10Amps. Suitable for low maintenance or maintenance free batteries which can be left permanently connected to the charger until required.

Battery Discharge Tester
The safe way to discharge test automotive batteries. Available in 12 or 24V versions and suitable for 20-120Ah (C20) capacity batteries. Allows hands free testing and come complete with heavy duty crocodile clips.
Size: 105H x 135W x 240D (mm). Wt 2.8kg.
12V ref BT12 B/5000156/1
24V ref BT24 B/5000156/2

DCVF Charger range
Automatic constant voltage float charging for secure DC power supply batteries (stationary wet or valve regulated lead acid). Can be used for 6, 12 and 24V systems with a DC output up to 10Amps and protected by a current limit to restrict the output to a safe level.
Size: 200H x 270W x 220D (mm). Wt 9.5kg comes complete with 1m AC and DC leads. Ref DCVF 12/24-10.
Applications: Automatic charging for batteries on Generator Sets, Ambulances, Fire appliances - tenders, caravans and boats.

R1211
Suitable for charging12V or 24V Wet or valve regulated Lead Acid batteries from 30Ah-70Ah. Fully automatic 8 Amp models. Controlled taper output with controlled voltage limits. Double insulated robust steel enclosure for shelf or wall mounting, rubber non-slip feet. Fitted with 13A mains plug, meets BS3456/3.25, EN60335/1 CDE0551.
Size: 200H x 270W x 220D (mm). Wt 6-8kg

Suitable for use both with electric wheelchairs and other battery powered applications.

Ref R1211 12V 8A (55Ah)
Ref R1211 24V 8A (70Ah)